TP-Link Helper manual

Version 1.0, November 2026. Idea by Jerry, made by Evie.

What it does

TP-Link Helper is a small Windows program for people with a TP-Link Wi-Fi router. TP-Link's own web page and app are hard to use with a screen reader, so this program does the most useful things from plain Windows lists, boxes and checkboxes:

It was made for screen reader users and tested with NVDA. Everything works from the keyboard.

What you need

Installing

  1. Unzip the zip file into a folder of its own that you can write to, such as C:\portable\TP-Link Helper. Don't use Program Files, because the program saves its settings in its own folder.
  2. Start "TP-Link Helper.exe".
  3. Windows may say "Windows protected your PC", because the program is new and not signed. Choose "More info", then "Run anyway".

There's nothing else to install. To move it, move the whole folder.

The first time you start it

A window called "TP-Link Helper router password" opens, with the cursor in the password box.

  1. Type your router's password. The letters show as stars. To hear them, check "Show the password" (Alt+S).
  2. Press Enter, or choose Save (Alt+V).

The main window opens, and the program checks your router right away. If the password is wrong, the Status box says so. Choose "Router password" (Alt+A) to type it again.

The program looks for your router at 192.168.0.1, TP-Link's usual address. If yours is different, close the program, open "TP-Link Helper settings.txt" in its folder in Notepad, change the line "router=192.168.0.1" to your router's address, save, and start the program again.

The main window

The controls, in Tab order:

Devices on your router (Alt+D)

The list. Devices on Wi-Fi come first, then the ones plugged in by cable ("wired"), then blocked or watched devices that aren't connected now. A line reads like:

"Den TV, 5 GHz-2, -61, good, address kept, watching, online 3 hours 12 minutes, used 2.3 GB, now 5.2 megabits down, under 0.1 up, 192.168.0.50"

Watch this device (Alt+W)

Check this to be told when the selected device drops off your router or comes back. Nothing is said the first time the program checks, only when something changes after that.

Block this device (Alt+B)

Checking it asks first, with No as the choice Enter gives. Yes blocks the device: it can't use your router at all, by Wi-Fi or by cable, until you uncheck this box. A blocked device stays in the list, saying "blocked", even when it can't connect, so you can always find it again to unblock it.

Routers won't block the computer that's managing them. If you try, the router quietly refuses, and the Status box says "Your router didn't block it."

Always give this device the same address (Alt+G)

Checking it keeps the selected device's current network address for it from now on, which helps with things like printers, or a TV you cast to. The device has to be connected when you check it. Unchecking it lets the device get any address again.

Name for this device (Alt+N)

Give the selected device a name you'll recognize, such as "Den TV". The list shows the new name once you leave the box. The name stays with that device, even if it gets a new network address. It's kept by TP-Link Helper only; the router's own name for the device doesn't change.

Some phones and watches make up a new hardware address now and then, for privacy. When that happens, they show up as a new device. TVs and streamers don't do this.

Label it on the router too (Alt+L)

Gives the router the name that's in the name box, so the router's own web page and the Tether app show it too. Type the name first (Alt+N), then press Alt+L. Names on the router can be 1 to 64 characters.

Priority for this device (Alt+O)

A list: Off, For 1 hour, For 2 hours, For 4 hours, Always. A device with priority gets your internet first when several devices are busy at once, such as a TV streaming while someone downloads. Arrow to the choice you want and stop; about a second later it goes to the router, and the Status box says so. A device has to be connected to get priority.

Priority only works while the router's QoS, its bandwidth manager, is on. The first time you give a device priority, TP-Link Helper turns QoS on, and the Status box says so. QoS works best when it knows your real internet speed; for now it uses the router's starting numbers.

Check every this many seconds (Alt+E)

How often to ask your router, 60 to start. From 10 to 3600 seconds (an hour).

Play a sound (Alt+S), Show a pop-up window (Alt+P), Show a Windows notification (Alt+F)

How you're told when a watched device drops off or comes back. The sound is a Windows sound unless you choose your own (below): one for bad news and another for good news. The pop-up window is called "TP-Link Helper message", with the cursor on the message, such as "Den TV dropped off your router." Press Escape, or Tab to OK and press Enter. The notification is a Windows notification, which NVDA reads out as it appears.

Sound when a device drops off (Alt+V) and Sound when it comes back (Alt+K)

These come right after "Play a sound". Each has a box for a sound file, then "Pick a sound..." to choose one, then "Play it" to hear it. A .wav or .mp3 file works. Leave the box empty to use a Windows sound. If a file can't be played, the Windows sound plays instead and the Status box says why, so a warning is never silent.

Start when Windows starts (Alt+R)

When checked, the program starts in the tray each time you sign in to Windows, and starts watching.

Status (Alt+U)

A read-only box saying when your router was last checked and how many devices are on Wi-Fi and by cable, such as "Checked at 7:42 PM. 9 on Wi-Fi, 2 wired." Problems and the results of blocking show up here too.

The buttons

The Wi-Fi settings window

In the main window, press Ctrl+Comma, or choose "Wi-Fi settings" (Alt+I). A window called "TP-Link Helper Wi-Fi settings" opens and reads your router's Wi-Fi settings. Unlike the main window, nothing here changes your router until you choose Save, because Wi-Fi changes knock devices offline for a moment. While this window is open, the main window's regular checks wait, because the router only lets one program sign in at a time.

Bands and guest networks (Alt+B)

Six lines: your router's three bands, then its three guest networks. A band reads like:

"5 GHz-1: Home Wi-Fi 5G, on, channel 48, width automatic, power High"

and a guest network like:

"Guest 2.4 GHz: Visitors, off, no password"

The Archer AX75 has a 2.4 GHz band and two 5 GHz bands: 5 GHz-1 uses the lower channels (36 to 64), and 5 GHz-2 the higher ones (100 to 165). The controls below the list are for the line selected in it.

For the selected band or guest network

A guest network shares its main band's channel, width and power, so for a guest network those lists say "Same as the 2.4 GHz band" (or whichever band it is) and can't be changed.

Guests can reach my own devices (Alt+G)

Unchecked to start, so guests only get the internet. Check it if guests should be able to cast to your TVs or print on your printer.

Status (Alt+U)

Says when the settings were read, whether you've changed anything that isn't saved yet, and how saving went.

The buttons

The Schedule and lights window

In the Wi-Fi settings window, choose "Schedule and lights" (Alt+S). A window called "TP-Link Helper schedule and lights" opens. Everything here goes to the router the moment you change it.

The Wi-Fi schedule

The router's schedule can't cross midnight. For the Wi-Fi to be off overnight, add two times: one from the evening to 12 AM (midnight, the end of the day), and one from 12 AM (midnight) to the morning. Each night's morning part belongs to the next day, so for Sunday night to Monday morning, the morning part is Monday.

The lights

Status (Alt+U) says what was saved, and Close (Alt+C, or Escape) closes the window.

The Firmware window

Firmware is the router's own built-in software. TP-Link sends out new versions now and then, to fix problems and close security holes. In the main window, choose "Firmware" (Alt+M). A window called "TP-Link Helper firmware" opens. While it's open, the main window's regular checks wait.

The automatic update choices go to the router the moment you change them, like the main window's choices.

The Internet speed and data used window

In the main window, choose "Your internet speed and data" (Alt+Y). A window called "TP-Link Helper internet speed and data used" opens. First the router itself tries to test its internet connection; that result is the speed coming into your home, not the speed of your Wi-Fi. Some routers' own tests fail every time (the Archer AX75's did when this was written). When that happens, this computer tests instead, using Cloudflare's free speed test server. A test from this computer also includes this computer's own Wi-Fi or cable, so it can be a little lower than the speed coming into your home.

Mbps means megabits per second. Streaming one HD video needs about 5 to 8, and 4K about 25.

Where the data used comes from: the Archer AX75 doesn't keep a monthly total of its own. It does know how much each connected device has used since it joined, so at every check TP-Link Helper adds up what each device used since the check before, and keeps the total in a file called "TP-Link Helper data used.txt" next to the program. That means:

Reading the signal

Wi-Fi signal is measured in dBm, a negative number. Closer to zero is stronger. The words the program uses (the same as T-Mobile Signal Watcher's):

SignalWord
-55 or bettervery good
-56 to -67good
-68 to -75fair
-76 to -82weak
-83 or worsevery weak

For streaming video, -67 or better is a good rule of thumb. Wired devices have no signal number.

Saving

In the main window there's no Save button. Every change is saved the moment you make it: names, checkboxes and numbers. A number box only saves a number that makes sense. While you're halfway through typing one, the last good number is kept. Blocking and keeping an address go to the router right away. Only the Wi-Fi settings window waits for Save.

The tray

While the program runs, its icon is in the system tray, the notification area by the clock. Its name is "TP-Link Helper".

Closing the window with Alt+F4 also only hides it. To close the program completely, use Exit. Starting the program again while it's running brings back the window that's already open.

If you can't find the icon, Windows may have put it in the hidden icons. Press Windows+B to go to the tray, then use the arrow keys.

Your password and privacy

If something goes wrong

Removing the program

  1. Uncheck "Start when Windows starts" (Alt+R).
  2. Choose Exit (Alt+X).
  3. Delete the program's folder.
  4. If you like, remove the saved password from Credential Manager, as described above.